Index >> Graphic Apps >> CAD >> VID
Report SpywareVID 1.152
Can not display screenshot
Software Description:
The VID (Virtual Instrument Desktop) SCADA HMI can use low cost Modbus hardware
The VID (Virtual Instrument Desktop) SCADA HMI software allows very low cost industry standard Modbus or NetCommander hardware to be used in
distributed control and monitoring systems. The Software combines a customizable virtual instrument display with event monitoring, logging, alerting and control systems, to provide a full and customizable HMI to your application.
The virtual instrument panel can comprise a variety of meters, dials, digital displays, graph plotters, thermometers, LED indicators,
control knobs, sliders, buttons and switches. These can be "connected" to a Netcommander monitoring point anywhere on the local
or World Wide network allowing data sources, temperature, pressure, voltages etc. to be visualised in seconds.
The instruments are viewed in multiple virtual screens; the current screen can be selected by using the toolbar forward, backward,
and page cycle buttons or from the drop down list of configured pages.
The system is equally "at home" with a local LAN or RS232/RS485 connected system or a globally distributed system using the Internet
or Corporate VPN.
Each NetCommander monitoring unit can provide up to 16 analogue input and outputs, 16 switch (relay) control outputs and inputs, .
The VID software will control up to fifty monitoring units.
Logs can be maintained and analysed for trends and compared week on week. Control schedules can also be set up.
The events system provides a configurable cause and effect system, several "causes" can be combined using AND/OR/NOT logic to
produce an event that can have several "effects". An "effect" can be a control output, raise an alarm, make a log entry send an e-mail or
SMS, run a control script etc. An almost unlimited number of events can be processed by the VID software, and a more limited number
can be processed by the NetCommander nodes natively, this will allow some basic control to be maintained autonomously,
in the event of network or PC failure.
What's New: Add flexmeters
Limitations: 1000000 Uses Trial; Will only run for 30 minutes at a time
The VID (Virtual Instrument Desktop) SCADA HMI software allows very low cost industry standard Modbus or NetCommander hardware to be used in
distributed control and monitoring systems. The Software combines a customizable virtual instrument display with event monitoring, logging, alerting and control systems, to provide a full and customizable HMI to your application.
The virtual instrument panel can comprise a variety of meters, dials, digital displays, graph plotters, thermometers, LED indicators,
control knobs, sliders, buttons and switches. These can be "connected" to a Netcommander monitoring point anywhere on the local
or World Wide network allowing data sources, temperature, pressure, voltages etc. to be visualised in seconds.
The instruments are viewed in multiple virtual screens; the current screen can be selected by using the toolbar forward, backward,
and page cycle buttons or from the drop down list of configured pages.
The system is equally "at home" with a local LAN or RS232/RS485 connected system or a globally distributed system using the Internet
or Corporate VPN.
Each NetCommander monitoring unit can provide up to 16 analogue input and outputs, 16 switch (relay) control outputs and inputs, .
The VID software will control up to fifty monitoring units.
Logs can be maintained and analysed for trends and compared week on week. Control schedules can also be set up.
The events system provides a configurable cause and effect system, several "causes" can be combined using AND/OR/NOT logic to
produce an event that can have several "effects". An "effect" can be a control output, raise an alarm, make a log entry send an e-mail or
SMS, run a control script etc. An almost unlimited number of events can be processed by the VID software, and a more limited number
can be processed by the NetCommander nodes natively, this will allow some basic control to be maintained autonomously,
in the event of network or PC failure.
What's New: Add flexmeters
Limitations: 1000000 Uses Trial; Will only run for 30 minutes at a time
100% Clean:
VID 1.152 is 100% cleanThis download (setup.exe) was tested thoroughly and was found 100% clean. Click "Report Spyware" link on the top if you found this software contains any form of malware, including but not limited to: spyware, viruses, trojans and backdoors.
Related Software:
- ABViewer 9.1 - CAD DWG DXF HPGL TIFF CGM SVG WMF STEP IGES STL SAT viewer, editor and converter
- Visual Drawing Maker 1.13 - Convert CAD files into self viewing executable (*.exe) files.
- MITCalc3D for SolidWorks 1.61 - Mechanical, Industrial and Technical Calculations for SolidWorks
- AutoQ3D CAD 5.10 - Full CAD application that let you make a lot of things in 2D & 3D
- progeCAD Professional AutoCAD Clone 2011.2.0.9 - progeCAD AutoCAD DWG Clone, 1/10th the cost, no learning curve for AutoCAD users
- DWF to DWG Converter 2007 2010 - Instantly convert DWF files to AutoCAD DWG and DXF files.
- AutoDWG Attribute Extractor 2.8 - AutoDWG Attribute Extractor, extract attribute information
- Maze Creator PRO 1.70 - Create random customized mazes with solution; add pictures, text, change shape
- ACAD DWG Viewer Pro 3 - DWGSee, a lite and fast DWG/DXF/DWF Viewer, batch print DWG/DXF/DWF files.
- VaryTable 2.1.0005 - Converts any selected text array in a CAD drawing into spread sheet cell table
top 10 most downloaded
recommended software
-
- 1AVCenter
- With 1AVCenter you can record your entire screen or part of it directly to AVI or WMV, capture screenshots in JPG, share your screen over the internet...
-
- IconEdit2
- Create and edit icon files for Windows, iPhone, iPad, Apple Watch, and Android with professional yet easy-to-use Icon Editor. IconEdit2 has full suppo...
